Friday, March 6, 2015

Dish Solar Concentrator Design



Over the next few months I will describe how I design point focus solar collector that will provide all the hot water and half the heat for my home. I will document how I manufacture the parts, assemble them, erect the structure, mount and align the mirror assemblies, connect the drives and plumb the receiver. The illustration below shows a computer model of an early version that has evolved over the past year.

Mirror Assemblies: Size, Quantity and Configuration
I will start by describing how I make mirror assemblies. They make up the concentrator and focus sunlight on a receiver designed to harness concentrated sunlight efficiently. Later I will cover the design of girders and trusses that support these components, the foundations required, and the gimbal that carries the concentrator and receiver. These all rotate together to follow the daily motion of the sun as well as allow all to follow the sun as it goes higher and lower in the sky through the seasons.


Computer Model of a Solar Dish with Mirror Assemblies and Receiver


A solar dish collector uses a concentrator to reflect sunlight into a receiver that transforms radiant energy into hot water or steam. The area of the concentrator may be 500 to 1,000 times larger than the opening of the receiver to minimize energy losses.  The receiver can be mounted close to the reflector, far away, or somewhere in between. Dividing the focal length, the distance from the mirrors to the receiver, by the concentrator diameter describes this (f/d) relationship. I work with an f/d ratio of 0.8, knowing that this works well with very high performance cavity receivers. Shorter focal lengths, say 0.6, require shallow cavities that lose more energy than deeper ones because hot surfaces inside lose more heat to wind and radiation. A longer focal length, say 1.0, where the receiver aperture is the same distance from the mirrors as the concentrator is wide, extends the receiver farther out from the main structure and requires more material and higher quality mirror assemblies.
Illustration Showing Various Focal Length to Diameter Ratios
Many point focus solar collectors have individual mirrors mounted on a structure to reflect images of the sun on a target. Attaching and aiming each one takes time and these individual mirror facets are difficult to clean. We made early solar collectors in the 1970s this way. We progressed to mechanically curved mirror assemblies that placed eight one-foot square mirrors end to end and were handled as a larger unit. Correct curves insure mirrors reflect sunlight to a spot. Mirrors are then continuous and easy to squeegee clean. Accurately curving aluminum extrusions is straightforward and simply attaching mirrors to them can establish a parabolic reflective surface that intensifies sunlight 30 to 60 times without having to adjust any mirrors. Attaching a few dozen of these assemblies to a structure and aligning them so they reflect sunlight to a single point creates the point focus concentrator. Permanently mounting mirrors in arrays minimizes labor when erecting a collector. An ideal: assemble and erect a solar collector in a single day. Accurately aligning mirror assemblies is easier and quicker than individually mounting nine to 16 times as many smaller mirror facets.

A specific design begins by choosing an appropriate size mirror assembly and then settling on a suitable array of these assemblies to make up the concentrator. Mirror facets come in many sizes and what I have on hand are 12”x12” and 12” x 36” mirrors that readily fit into square panels that are either three or four feet square or rectangles that are three by four foot. One person can readily handle these mirror assemblies. A 3’ x 3’ weighs 10 pounds and the larger ones weigh less than 20 pounds.

The table below shows a few ways that mirror assemblies can be arranged in a concentrator. A roughly circular arrangement gives each mirror a good view of the inside of the receiver. The farther away from the optical axis (a line through the centers of the concentrator and receiver) a mirror is, the poorer view it has of the inside of a cavity receiver, making it less effective than those closer to the center.


Mirror Assembly Configurations with Table of Mirror Area & Quantity
At this point I’m leaning toward configuration “C” that has 16 four-foot square mirror assemblies. In an hour in bright sun these would reflect 24 square meters of sunlight, 20 or more kilowatts, into a receiver that would displace burning five pounds of fuel oil and releasing over 11 pounds of carbon dioxide when I burned oil for heat and hot water. Over a year it should halve how much wood I have to gather and work into pieces for the stove: maybe by three cords, or six tons. I should be able to manufacture 16 mirror assemblies in a day or two and to fix and align them on the concentrator structure in one night so they hit a target.

It is easier to work in the dark using an LED flashlight shining at a mirror assembly, MA, from the center of a target at twice the focal length. Tighten the bolts at the four corners when it reflects the image to the target center. One could use sunlight during the day to do this but after aligning a few mirror assemblies the target becomes so bright it becomes impossible to see the reflection of a single MA. One could cover each fixed MA but this is cumbersome. Also, using the sun during the day works well around noon, when the concentrator faces up and is level, but because the structure must be tracking the sun for the process to work, climbing around the tilted moving structure in the morning or late afternoon becomes more difficult. And sunny days without clouds often don’t occur when you want them. Every night is dark, though, and working close to the ground with a stationary structure looks easier so we will be exploring this new MA mounting and alignment technique for this project.

Sunday, March 1, 2015

Choosing a Solar Collector

 Peak oil, climate change and sustainability require developing energy resources that are freely available, affordable and don’t alter the atmosphere or oceans. Why not start providing energy for our homes and public buildings because they don’t move and they consume a third of our fossil fuels? Wind turbines feed power into the grid but many homes and farms do not have reliable wind for direct power, hot water and comfort. Sun shines everywhere and solar collectors can augment many living situations. There are many kinds of solar collectors: flat plate types that simply utilize the sunlight that shines on them, those that intensify sunlight from a few times and up to 50 times, and those that concentrate solar energy a few hundred to over 1,000 times. Which is most useful?

Earth is in the sun’s Goldilocks zone: not too hot, and too cold. Natural sunlight is just right. We wouldn’t be here if the sun didn’t support plants and animals. But to gather enough sunlight to do the useful work we’ve come to expect requires utilizing energy from large areas. Economics favor using inexpensive mirrors to intensify sunlight on a small area that will pay for high-tech approaches (like high temperature materials and insulation) to harvest most of the available energy. Flat plate solar collectors, both photovoltaic and thermal, use materials that would be too expensive without government subsidies and perform poorly (PV delivers <15% and thermal even less when it’s cold). Passive solar designs use windows to contribute heat for buildings but today’s active systems cost too much.

Prototype Dish Solar Collector: Work Begins in 2015 on One That Has About Four Times More Mirror Area
Parabolic trough solar collectors that intensify sunlight from 20 to 50 times are popular for generating power and typically use glass envelopes to surround the metal tube that contains the working fluid inside with the volume between evacuated like a Thermos bottle. To allow the metal and glass to expand at different rates without breaking, they need a flexible metal bellows to join the two materials.  These receiver assemblies are quite expensive and when they lose vacuum they must be drained, cut out and a new one welded in place. Again, without subsidies, they are too expensive.

Concentrating photovoltaic collectors, parabolic dishes and solar power towers intensify sunlight from 300 to a few thousand times. This allows receivers to work well without vacuum enclosures because the high intensity energy can be efficiently captured without a window or vacuum enclosure (typically capturing above 90% even when it's below freezing). Economics favor higher concentrations because inexpensive optical elements direct large amounts of sunlight into tiny receivers. Using 450 mirrors, a square foot each at a dollar, to intensify sunlight 900 times requires a small, well-insulated trash pail size receiver with a 9-inch diameter opening to collect 34 kilowatts in bright sunlight. Each hour this collector would deliver the same amount of steam as a fossil fueled boiler burning a gallon of fuel oil or 1.5 gallons of propane. The same concentrator with a CHP (combined heat and power) receiver would deliver 10 kilowatts of power and 20 of heat.


Taking Apart the Engineering Prototype Solar Dish
The few dish solar collectors available today are complicated and require experts and cranes to install them. This year I hope to demonstrate a new approach to building solar dishes that enables anyone to make the parts in their home shop, put them together, accurately align mirrors and let a simple open-source controller run it for 30 years, custom programming and setup not required. I hope that the availability of inexpensive and fun to make solar equipment will enable others to develop receivers and applications that enable very high performance renewable energy systems to displace major amounts of fossil fuels.

Thursday, February 12, 2015

Native Albany Pine Bush Preserve Plants


My earlier post described processes involved in cleaning wild flower seeds being propagated to replace invasive species in the Albany, NY, Pine Bush Preserve. These flowers should provide nectar for Karner Blue butterflies that live there and are endangered. 

My Introduction: Bagged Dried Horsemint Flowers
Jesse's Earlier Step: Harvested NJ Tea Seed Heads Laid Out for Drying
Below are photos of some of the plants that produced the seeds we cleaned last week. Jesse Hoffman took these and shared them to illustrate what they look like when all decked out in flowers and how they are laid out to dry after harvesting.


Horsemint Closeup

Horsemint Mid Range View
Horsemint from a Distance
Horsemint Seeds in Ever Cleaner Stages
New Jersey Tea Closeup
New Jersey Tea
Bagged New Jersey Tea
Cleaning Stages: New Jersey Tea
Bush Clover
Showy Tick Trefoil Closeup
Showy Tick Trefoil

Thursday, February 5, 2015

Cleaning Seeds

The past few days I had a wonderful time helping a friend, Jesse Hoffman, transform more than a dozen large leaf bags filled with seed heads of flowering plants to five small bags of clean seeds. Jesse has been doing this process at the Big Flats, New York, Plant Materials Center near Corning, for a few years: http://www.nrcs.usda.gov/Internet/FSE_DOCUMENTS/nrcs144p2_015104.pdf . This is one of 27 plant materials centers operated by the United States Department of Agriculture, Natural Resources Conservation Service that serves northeastern states. It's an incredibly valuable resource for the region.

Jesse is the Preserve Steward and Botanist at the 5,380 acre Albany Pine Bush Preserve, www.albanypinebush.org,  a local and national treasure that harbors rare and endangered species including the federally endangered Karner blue butterfly, two rare natural communities and fourteen rare insects. His responsibilities include replacing invasive species with native plants that help endangered insects flourish. His staff, volunteers and seasonal workers gather seed heads from selected varieties and after drying them, place them in bags. They concentrate on wild lupine which is the only plant that Karner Blue butterflies feed on and have that cleaned at the New York State Tree Nursery: http://www.dec.ny.gov/animals/7127.html in Saratoga Springs because the very large quantity of pods is too difficult to transport to the Finger Lake region. We processed New Jersey Tea, Showy Tick Trefoil, Bush Clover, Butterfly Weed, and Horsemint.


The first step tears apart the pods or seed heads to release the individual seeds using either a hammermill or a seed brushing machine. Both force the plant matter through one of a variety of screens with different size holes. The next operation then separates the mix of materials through more screens using a combination of shaking and blowing to separate the materials that are larger than (scalpings), smaller than or lighter than single seeds. This often required repeating the process a few times to remove different sizes of extraneous material to end up with pure seed. A great tool for finishing was the Clipper Office Tester, http://www.atferrell.com/clipper/products/clipper-office-tester that is small, easy to reconfigure using a large selection of screens, and runs quietly.  For the first separation process we typically used a larger, floor mounted, model, and for one type, an even larger model cleaner to remove the tiny seeds from five large bins of hammer milled material.

We had budgeted more than two days, including two overnights, but finished in less so we could get home on the second day. This was only possible because Jesse had processed each variety before and knew exactly what size reducing process and screen size was best for each, and then what machine, screen sizes and air blowing settings gave good results for the final separation and cleaning steps. 
Two Types of Seed Heads: Bush Clover and Horsemint

Hammer Mill Screen Options

Hammer Mill Open, Without a Screen
Seed Brushing Machine from Denmark
Screens for Seed Brushing Machine
Open Seed Brushing Machine Showing Brushes, Without Screen
Clipper Office Tester w/ Bins for Scalpings, Seed, and Light Fractions
Cabinet Full of Screens with Different Hole Types & Sizes
Sample of Screens Showing Various Hole Sizes

Jesse Feeding Floor-mounted Seed Cleaner







Wednesday, January 28, 2015

Divest Big Energy: But Better Solar Tools Needed to Live Without Changing Our Climate

Divesting in firms that extract fossil fuels makes powerful statements but does not reduce responsibility for keeping fossil carbon deep underground. Corporation profit when we buy fuels and power to drive, fly, heat our homes, and warm our showers.

Solar power charges electric cars, cools homes and runs lights and appliances.  But available solar thermal systems are small and expensive. We need larger inexpensive high performance solar collectors for heating homes, making alternative fuels and powering industry. I’ve been working to perfect solar dishes for over 40 years enabling them to perform well in winter. We need simple,
high performance solar collectors that:

   1. Intensify sunlight 1,000 times to power tiny receivers that deliver heat and power;
   2. Harvest more than 80% of available sunlight;
   3. Are made with home shop tools without welding or expensive equipment;
   4. Can be installed using hand tools and then operate without expert attention;
   5. Replace in less than six months the energy invested in making it;
   6. Operate for 30 years: all parts easily repaired or replaced;
   7. Utilize only materials that can be readily reused or recycled;
   8. Power both themselves and connected systems so they work after storms;
   9. Provide year-round hot water, air conditioning and space heating; and
  10. Pay for themselves in fewer than ten years, without subsidies.

Solar Collector Integrated with Outdoor Burner Readily Provide Comfort Year-round
Working alone, progress is slow. Anyone interested in helping make solar tools that enable life without burning fossil carbon?

Wednesday, January 21, 2015

A Solar Furnace - Anyone?

Yesterday a bright yellow plastic bag with a fuel delivery ticket inside hanging on her mailbox flag announced that my neighbor just received 389 gallons of #2 fuel oil. Her farmhouse is empty because she now lives in an assisted living facility but to prevent mold issues and keep toilets, traps and pipes from freezing she has the thermostat set at 50 degrees. I’ve been looking after her place for years as her husband’s health failed, then passed away and her own health deteriorated. Later this spring her home that sits on 57 acres and where her family lived for 40 years is under contract for sale.
Fuel Oil Delivery Ticket: 388.8 gallons 10-24-14 to 1-19-15

The coming deadline gives me almost three months to cut dead or dying trees along fencerows and gather fallen branches that make good firewood. I’ll miss checking the indoor temperature every day by glancing, from outside, at the large thermometer hanging inside her kitchen window. I’m usually on skis chasing my daughter who is much faster than I and we always include this point in our varied routes that cover two or three miles. The snow melted this past weekend so we’re covering rougher terrain on foot, looking for signs of owls, fox and coyotes because they are unusual compared to mice, rabbits and the four dozen deer we saw yesterday.

So far this heating season it’s taken over a ton and a half of fuel oil to keep her farmhouse from freezing. It would have taken more to maintain 65 degrees. Since we’re midway through the heating season, it’ll take more than 3 tons of fossil oil costing more than $2,500. Carbon dioxide contribution to the atmosphere? 17,400 pounds, almost nine tons! Could solar do better? Not without a lot of progress that no one seems to be addressing.

The sun often shines 15 hours during a day in June when it’s warm but energy is needed for only for heating water for washing and showers. Because upstate New York is downwind from the great lakes, we get very little sun during November and December when home heating issues become serious. Burning wood for heat is popular and most neighbors have a parlor stove or fireplace insert to reduce the cost of heating with electricity, propane or oil. In rural New York there are no natural gas lines so we don’t have that option.

One carbon neutral approach for using high performance solar collectors would be to combine them with furnaces that burn either wood pellets or cordwood. Pellets can be delivered in bulk and ignited/fed automatically so tasks become adjusting the thermostat and emptying ash.  Wood chunks have to be created by cutting trees, hauling logs and branches, and reducing them to sizes that are easy to handle. And they have to be strategically loaded into the firebox filled with coals. A cold firebox requires the extra work of lighting kindling. A solar collector could supplement these burners so keeping warm would require only half the wood. In our case we would have to process only 12,000 pounds of wood instead of 12 tons. For six months solar would provide both hot water and heat: no need to start fires. But we’d have to handle wood in bad weather during the coldest months, a process that I’ve enjoyed for decades. It keeps me active and often exposed to awesome starry skies, meteors and northern lights that I would not see if I stayed indoors.


Combining a Solar Collector with an Outdoor Wood Furnace

We’re developing solar technology so folks in rural communities can fabricate components, assemble solar collectors and use them for 30 years heating water and homes.  These solar collectors still need appliances like air conditioners, clothes driers, cooking appliances or thermochemical reformers so that they utilize the abundant energy available at temperatures up to 1,000 degrees during the summer. Intensifying sunlight 1,000 times even here in the cloudy northeast, these high performance solar collectors readily collect 80% of the energy available and return money invested in an installation without subsidies in five years and energy invested in the equipment in five months. Not using sunlight available during the summer extends these paybacks. These costs do not include backup heating equipment needed to keep warm when the sun doesn’t shine, stored heat has cooled down and it’s getting cold. Homes already have hot water and central heating so these can fill in when there is not enough sunlight.